3D Printing - DIG005AS3AE - Opinto-opas

3D Printing, 3 cr - DIG005AS3AE

Upcoming implementations

3D Printing DIG005AS3AE-3004 20.05.2024-24.05.2024 3 op (CONTACT, ...) +-
Campus

Pasila Campus

Teaching language

English

Timing

20.05.2024 - 24.05.2024

Enrollment

02.01.2024 - 17.05.2024
Groups
- CONTACT
- INTENSIVE
- SUMMER
Teachers

Heikki Hietala, Juho Kastemaa

Seats

15 - 40

Degree Programme

TRATI Tradenomi tietojenkäsittely

R&D proportion

0.00 cr

Virtual proportion

0.00 cr

Evaluation scale

H-5
3D Printing DIG005AS3AE-3008 12.08.2024-16.08.2024 3 op (ITE3PADIG1, ...) +-
Teaching methods and instruction

This course presents the use of fused deposition printers (FDM) and resin printers (SLS).

PLEASE NOTE THIS:

An absolute prerequisite for this course is a passed MUM 8TA001 Basic 3D Design with Blender course. If this is not your case, please do not apply.

Learning material and recommended literature

This is a hands-on course, with some theoretical information at first.

Working life connections

After this course, students are able to run various printers using Cura, RepetierHost and PreForm.

Campus

Pasila Campus

Exam dates and re-exam possibilities

No exam.

Teaching language

English

Internationality

-

Timing

12.08.2024 - 16.08.2024

Learning assignments

This course has one mandatory modeling and printing task, and 4 tasks to be designed and printed by the students.

Content scheduling

Intensive week, contact lessons Mon to Fri 10 to 16.
Groups
- ITE3PADIG1
- CONTACT
- INTENSIVE
- IT3PADIG1
- EXCH
- ITB3PADIG1
Alternative learning methods

This course can be completed with recognition of prior learning.

Teachers

Heikki Hietala

Seats

15 - 40

Further information

Models and prints 0 to 5.

Degree Programme

TRATI Tradenomi tietojenkäsittely

R&D proportion

0.00 cr

Virtual proportion

0.00 cr

Evaluation scale

H-5
3D Printing DIG005AS3AE-3006 07.01.2025-10.01.2025 3 op (ITE3PADIG1, ...) +-
Campus

Pasila Campus

Teaching language

English

Timing

07.01.2025 - 10.01.2025
Groups
- ITE3PADIG1
- CONTACT
- INTENSIVE
- IT3PADIG1
- EXCH
- ITB3PADIG1
Teachers

Heikki Hietala

Seats

15 - 40

Degree Programme

TRATI Tradenomi tietojenkäsittely

R&D proportion

0.00 cr

Virtual proportion

0.00 cr

Evaluation scale

H-5
3D Printing DIG005AS3AE-3007 19.05.2025-23.05.2025 3 op (CONTACT, ...) +-
Campus

Pasila Campus

Teaching language

English

Timing

19.05.2025 - 23.05.2025
Groups
- CONTACT
- INTENSIVE
- SUMMER
Teachers

Heikki Hietala

Seats

15 - 40

Degree Programme

TRATI Tradenomi tietojenkäsittely

R&D proportion

0.00 cr

Virtual proportion

0.00 cr

Evaluation scale

H-5
Show all (4) Hide

Current implementations

No ongoing implementations yet.

Past implementations

3D Printing DIG005AS3AE-3009 18.03.2024-22.03.2024 3 op (ITE3PADIG1, ...) +-
Learning material and recommended literature

Intensive week course, with a Moodle virtual environment

Campus

Pasila Campus

Teaching language

English

Timing

18.03.2024 - 22.03.2024

Enrollment

02.01.2024 - 15.03.2024
Groups
- ITE3PADIG1
- IT4PADIG1
- CONTACT
- ITE4PADIG1
- ITB4PADIG1
- INTENSIVE
- IT3PADIG1
- ITB3PADIG1
Teachers

Juho Kastemaa

Seats

15 - 40

Degree Programme

TRATI Tradenomi tietojenkäsittely

R&D proportion

0.00 cr

Virtual proportion

0.00 cr

Evaluation scale

H-5
3D Printing DIG005AS3AE-3003 08.01.2024-12.01.2024 3 op (ITE3PADIG1, ...) +-
Teaching methods and instruction

Tällä kurssilla tutustutaan 3D-tulostukseen käyttäen lankatulostimia (FDM) ja hartsitulostinta (SLS).

Kurssille pääsyn ennakkoedelltyksenä on MUM8TA001 Basic 3D Design with Blender -kurssin hyväksytty suoritus

Learning material and recommended literature

Kurssi on tulostamisen oppimista käytännössä, pienen teoriaosuuden jälkeen.

Working life connections

Tämän kurssin jälkeen pystyy tulostamaan sekä FDM- että hartsitulostimilla käyttäen Curaa, Repetierhostia ja PreFormia.

Campus

Pasilan toimipiste

Exam dates and re-exam possibilities

Ei tenttiä.

Teaching language

Finnish

Internationality

-

Timing

08.01.2024 - 12.01.2024

Learning assignments

Kurssilla on yksi pakollinen mallinnustehtävä joka tulostetaan ja 4 vapaavalinnaista mallinnis-tulostustehtävää.

Enrollment

02.01.2024 - 05.01.2024

Content scheduling

Intensiiviviikko, lähitoteutus ma-pe 10-16
Groups
- ITE3PADIG1
- HETIPAVV
- CONTACT
- INTENSIVE
- IT3PADIG1
- EXCH
- ITB3PADIG1
Alternative learning methods

Tulostuskurssin voi suorittaa näytöllä.

Teachers

Heikki Hietala, Juho Kastemaa

Seats

15 - 40

Further information

Mallit ja tulosteet 0-5

Degree Programme

TRATI Tradenomi tietojenkäsittely

R&D proportion

0.00 cr

Virtual proportion

0.00 cr

Evaluation scale

H-5
3D Printing DIG005AS3AE-3005 14.08.2023-18.08.2023 3 op (ITE3PADIG1, ...) +-
Teaching methods and instruction

This course presents the use of fused deposition printers (FDM) and resin printers (SLS).

PLEASE NOTE THIS:

An absolute prerequisite for this course is a passed MUM 8TA001 Basic 3D Design with Blender course. If this is not your case, please do not apply.

Learning material and recommended literature

This is a hands-on course, with some theoretical information at first.

Working life connections

After this course, students are able to run various printers using Cura, RepetierHost and PreForm.

Campus

Pasila Campus

Exam dates and re-exam possibilities

No exam.

Teaching language

English

Internationality

-

Timing

14.08.2023 - 18.08.2023

Learning assignments

This course has one mandatory modeling and printing task, and 4 tasks to be designed and printed by the students.

Enrollment

12.06.2023 - 11.08.2023

Content scheduling

Intensive week, contact lessons Mon to Fri 10 to 16.
Groups
- ITE3PADIG1
- HETIPAVV
- CONTACT
- INTENSIVE
- IT3PADIG1
- EXCH
- ITB3PADIG1
Alternative learning methods

This course can be completed with recognition of prior learning.

Teachers

Heikki Hietala

Seats

15 - 40

Further information

Models and prints 0 to 5.

Degree Programme

TRATI Tradenomi tietojenkäsittely

R&D proportion

0.00 cr

Virtual proportion

0.00 cr

Evaluation scale

H-5
3D Printing DIG005AS3AE-3002 22.05.2023-02.06.2023 3 op (CONTACT, ...) +-
Teaching methods and instruction

Tällä kurssilla tutustutaan 3D-tulostukseen käyttäen lankatulostimia (FDM) ja hartsitulostinta (SLS).

Kurssille pääsyn ennakkoedelltyksenä on MUM8TA001 Basic 3D Design with Blender -kurssin hyväksytty suoritus

Learning material and recommended literature

Kurssi on tulostamisen oppimista käytännössä, pienen teoriaosuuden jälkeen.

Working life connections

Tämän kurssin jälkeen pystyy tulostamaan sekä FDM- että hartsitulostimilla käyttäen Curaa, Repetierhostia ja PreFormia.

Campus

Pasilan toimipiste

Exam dates and re-exam possibilities

Ei tenttiä.

Teaching language

Finnish

Internationality

-

Timing

22.05.2023 - 02.06.2023

Learning assignments

Kurssilla on yksi pakollinen mallinnustehtävä joka tulostetaan ja 4 vapaavalinnaista mallinnis-tulostustehtävää.

Enrollment

02.01.2023 - 19.05.2023

Content scheduling

Intensiiviviikko, lähitoteutus ma-pe 10-16
Groups
- CONTACT
- INTENSIVE
- KESÄ2023
Alternative learning methods

Tulostuskurssin voi suorittaa näytöllä.

Teachers

Heikki Hietala

Seats

15 - 25

Further information

Mallit ja tulosteet 0-5

Degree Programme

TRATI Tradenomi tietojenkäsittely

R&D proportion

0.00 cr

Virtual proportion

0.00 cr

Evaluation scale

H-5
Show all (4) Hide

Upon successful completion of the course, the student is able to

operate and maintain the various printer types of the 3D LAb
design a mesh in Blender
export it to STL file format
check the manifold properties of the mesh
use RepetierHost or Cura to manage the printing process
adjust the mesh and re-export the mesh until perfect

Understanding 3D printing
Understanding the path from Blender meshes via manifold checking to STL file and printer
Printer materials (ABS, PLA, nylon)
Fused Deposition Manufacturing type printers (MiniFactory, CoLiDo models, BCN3D)
RepetierHost printer management software and using memory card for transferring print jobs
Managing the printing process
Hands-on training on a variety of 3D printer models

This intensive week course is designed to take the student one step further in 3D, namely to design a mesh and take it through the 3D printing process. With 8 printers available, a limited intake of students will be effected with max 20 students attending.

Students will then learn how to design, prepare and print their own designs, and it is planned that this course will enable students then to use the printer lab at their own discretion.

Intensive week course, with a Moodle virtual environment

This course is for those who have taken the DIG012AS2AE Basic 3D Design with Blender. On this course you will learn 3D modeling for making prints in filament printers as well as our top of the line SLA Resin printer. After the course you will be ready to take on 3D print work for clients, such as YLE, for which we produced 132 medals for a drama series. YLE has returned for to us and we are building 3D printed, robotic parts for their children's programs. This course is for anyone who has acquired the basic modeling skills and is willing to expand their skills towards physical objects from virtual meshes. After this course you may be able to use your skills in DIG006AS3AE 3D Extended course, if we have a client who needs 3D print work.

Should a student already possess the knowledge and practice of 3D printing, it is possible for that student to design a mesh in the 3D package of his/her choice and then take it through the printing process from the STL file stage onwards. If the person has 3D prints that he/she has printed previously and individually, these can be considered at the teacher’s contact hour.

DIG012AS2AE Basic 3D Design with Blender MUST be taken prior to this course with a good grade, or, the student must display adequate design competence using Blender, 3DS Max, or Cinema 4D.

Any other 3D package can be considered, if it exports STL file format files.

The student

has a passable knowledge of the 3D design process
understands the use of different file formats
understands the significance of the concept of manifold objects
manages to create a very simple printable mesh
manages to take the object through the printing process and the result is a small and simple 3D printed object

The student

has a good knowledge of the 3D design process
understands the use of different file formats and is able to move between file formats as necessary
understands the significance of the concept of manifold objects and uses tools to check for manifold properties
manages to create a more complex printable mesh
manages to take the object through the printing process and the result is a relatively complex 3D printed object

The student

has an extensive knowledge of the 3D design process
understands the use of different file formats and is able to move between file formats as necessary
understands the significance of the concept of manifold objects and uses tools to check for manifold properties
manages to create a very complex or multi-part printable mesh
manages to take the object through the printing process and the result is a complex or multi-part 3D printed object

Grades 1 - 5.